Phase-change material in 2010s: Cold-chain packs — Section 1094: Cold-chain packs
Dossier 1094 for Phase-change material links case “Cold-chain packs” directly to metric 21 (2010s). The wrong grade is the most expensive hazard. Keep Phase-change material with “Cold-chain packs” and 21 from 2010s. Assemblies (EI, R, Type X) are not implied by the material letter.
Scores compare Phase-change material with the rest of the atlas on strength, heat, fire behaviour, insulation, workability and circularity. They are editorial, not certificates. Seven chapters follow. Fire and insulation claims name test families (Euroclass, ASTM E84, ISO 5660, KS F) rather than inventing a single safety number.
Phase-change material (paraffins / salt hydrates / bio-waxes) is a family of grades whose density ~0.8–1.6 g/cm³, heat band designed 18–28 °C for buildings, and fire letter paraffin = combustible; salts vary. Phase-change material is sold as grades, not as a single substance. Chemistry paraffins / salt hydrates / bio-waxes, density ~0.8–1.6 g/cm³, heat band designed 18–28 °C for buildings.
This atlas treats Phase-change material as a system: mill route, coatings, tests and the cavity it sits in. Conductivity note: low-to-moderate; often needs fins or graphite. Insulation score 52/100 is relative to 32 entries — metals lose, VIPs and aerogels win. Fire letter in editorial use: paraffin = combustible; salts vary. Do not equate A1 with “safe in a blaze” or E with “illegal”. Assemblies decide.
The label keeps Phase-change material, 2010s, and 21. “Cold-chain packs” is the condition on the figure. Keep Phase-change material with “Cold-chain packs” and 21 from 2010s. 212010s
Figures to keep
- Reference
- 2010s
- Key figure
- 21
- Topic
- Phase-change material
- Focus
- Cold-chain packs
Interactive Scenario & Decision Matrix
Select your current objective to inspect the recommended benchmark, threshold, and verification path.
Keep heat resistance {heat}.
Briefing 11 for Aerogel aligns condition “Kistler” with reference value 0 on the ground.
Aerogel: 0 (1931)Keep the thermal line {therm0}.
Reading 12 of Aerogel uses “Lab curiosities” and figure 80 as a checkable baseline.
Aerogel: 80 (1960s)Use {therm0} only if it agrees with score {heat}. If they conflict, do not pick a product from this page.
Atlas note 13 on Aerogel defines the operating range of 0 when “NASA Stardust” applies.
Aerogel: 0 (1990s)Reading 4 of Aerogel uses “Aspen Aerogels” and figure 0 as a checkable baseline.
Dossier 14 for Aerogel links case “Aspen Aerogels” directly to metric 0 (1998).
Aerogel: 0 (1998)United States (US) Institutional & Field Benchmark
US- Primary reference framework
- Metals, textiles, polymers, ceramics, and thermal/fire families with locale standards lenses.
- Verification standard
- Season lens: moisture, freeze-thaw, and fire season change how materials fail outdoors — check climate notes on each page.
- Metric & unit convention
- Aerogel · 0 (1931)
Material pages compare grades, process, and fire/thermal behavior for browsing — not a substitute for building codes or structural engineering.
Self-Diagnostic Readiness Checklist
Baseline stage (0–1/5): verify primary definitions and core thresholds before acting.
5-Step Execution & Verification Playbook
- Read the fire-performance mark — Fire on this hub is {fire}/100 — teaching comparison among atlas materials.
- Read the insulation mark — Insulation is {insul}/100 — heat-flow story, not the same question as flame.
- Sit one published fact beside them — Quick fact on file: {fact0}.
- Sustainability is not a fire skip — A high sustainability mark does not replace fire protection in a real assembly.
- Not a building-code rating — Named tests, thickness and build-up still decide compliance — this page is literacy only.
Myth vs. Evidence Fact-Check
Is the fire-performance score a building-code rating?
No. It is an editorial 0–100 teaching mark among materials in this atlas. A real wall or garment needs a named product test, thickness and assembly. This page is not a lab stamp.
When should I read insulation instead of fire?
Use the insulation pick when the question is heat flow — lining, loft, or a cold-bridge — and the fire pick when the question is how the same material behaves in flame. Both numbers already sit on this hub; they answer different jobs.
Does a high sustainability score mean I can skip fire protection?
No. Sustainability here is a relative atlas mark (growth, reuse, embodied story). Bamboo and timber can still char like wood. Fire protection stays a separate specification.
Why is bamboo missing in some languages?
A language URL is published only when the seven chapters are real prose in that language. Bamboo exists in English, Korean, Japanese, Chinese and Spanish. French, German, Portuguese and Russian stay withheld — earlier machine drafts leaked English, so those URLs are not opened.
Domain Jargon & Terminology Decoder
- 1
- Name the use environment (load, moisture, fire, chemicals).
- 2
- Note which standards market you are in.
- 3
- Pair mechanical claims with fire/thermal notes.
- 4
- Verify with current standards before specifying.
- Aerogel (Cabot particles)
- Analysis 65 for Aerogel anchors “Cabot particles” to indicator 0 so readers can verify the scale.
- Aerogel (EN 13501 blankets)
- Record 66 on Aerogel explains what the threshold 13501 means in practice under “EN 13501 blankets”.
Risk & Failure-Mode Early Warning Radar
- Not a building-code manual, SDS substitute, or structural calculation. Always verify with licensed professionals and current standards.
- Section 72 on Aerogel pairs “Lab curiosities” with benchmark figure 80 (1960s) for a grounded decision.
- Analysis 73 for Aerogel anchors “NASA Stardust” to indicator 0 so readers can verify the scale.
- Record 74 on Aerogel explains what the threshold 0 means in practice under “Aspen Aerogels”.
Phase-change material in 2020s: Bio-based waxes — Section 1095: Bio-based waxesNext essayAll 1100 essays1100